Home / Goalie Play

How to String a Lacrosse Goalie Head: Pocket, Channel, and Outlet Test

How to String a Lacrosse Goalie Head: Pocket, Channel, and Outlet Test

Photo: Pixabay / Pixabay

What a Goalie Pocket Must Do That a Field Pocket Must Not

A field pocket is built to hold, cradle, and release quickly. A goalie pocket is built to absorb a shot traveling faster than any pass, kill its rebound, and then throw a long, accurate outlet pass while the goalie is still standing in the crease. Those jobs pull the design in opposite directions. A deep, soft bag swallows shots but throws rainbows. A shallow, tight pocket throws lasers and gives up rebounds that become second goals. Stringing a goalie head is the art of landing between those failures, and this guide walks the job in the order a stringer actually works.

Goalie heads are up to 12 inches wide and use large diamond mesh, most commonly 12 diamond, because small diamond mesh across that width forms a tennis racket that shots blow through or bounce off. Everything below assumes a standard goalie mesh kit with top string, sidewalls, bottom string, and shooting strings.

Materials and Head Setup

ComponentGoalie choiceReason
Mesh12 diamond goalie mesh, soft or semi softLarge diamonds wrap the ball and damp rebounds
Top stringSturdy nylon, strung center outSymmetry at the scoop controls the whole channel
Sidewall stringStandard sidewall cord, generous lengthA wide head consumes far more string than a field head
Bottom stringAdjustable, left accessible after the jobThis is your depth and rebound tuning control
Shooting stringsTwo or three, woven flatThey tune outlet trajectory without tightening the bag
ToolsPliers, scissors, lighter, a ball for poundingKnots on a wide head need real tension

Seat the head on the shaft and snug the screw before you string. A pocket tuned on a loose head changes character the moment the head is mounted and tightened.

Interactive tool

Goalie Pocket Finish Check

Check off each step as you finish it. Your progress stays on this page.

0 of 8 complete

0% done

Step by Step: Building the Pocket

  1. Find the center of the mesh and attach the top string at the scoop, working outward from the middle so both sides mirror each other exactly.
  2. Lock the top corners down tightly. Loose corners are the main cause of a goalie pocket that throws sideways.
  3. Run the sidewalls from the top, interlocking the large diamonds and pulling tension that draws the mesh down into a channel rather than across like a drum.
  4. Place the deepest part of the pocket just below the center of the head, where it can cradle a saved ball during a clear without sitting illegally deep.
  5. Weave the bottom string and leave it adjustable. Set initial depth so a ball placed in the pocket sits with its top roughly level with the bottom edge of the sidewall, then tune from there.
  6. Pound the pocket hard with a ball, working the mesh around a full ball shape, because goalie mesh stretches more than field mesh.
  7. Weave two shooting strings across the upper third, flat and snug, adding a third only if outlet passes float.
  8. Run the rebound test and the outlet test below, adjust one element at a time, and only then trim the strings.

The Two Tests That Decide Whether the Pocket Is Finished

The rebound test: have a partner throw or shoot firm balls into the pocket from eight to ten yards while you hold the stick in your stance without moving it. A good pocket catches and holds at least eight of ten, with rebounds dropping at your feet rather than bouncing back into the slot. Rebounds flying forward mean the pocket is too tight or too shallow. Balls blowing through or pulling the stick mean the mesh is too soft or the sidewalls too loose.

The outlet test: throw twenty passes at a target twenty five to thirty yards away. A good goalie pocket releases on a firm, slightly rising line that a midfielder can catch at chest height in stride. Passes that sail mean the channel is too open at the top or the shooters are too loose. Passes that dump into the ground mean the bag is too deep or a shooter is acting as a brake. Fix trajectory with shooters first, depth with the bottom string second, and sidewall tension only if both tests fail together.

Legality for a Goalie Pocket

Goalie pockets may be deeper than field pockets, but they are not unlimited. The standard test used for a mens goalie crosse is that the top of the ball, when placed in the pocket, must not be deeper than the bottom edge of the sidewall, and the complete goalie stick must measure inside its legal range, 40 to 72 inches in the boys and mens game and 35.5 to 52 inches in the girls and womens game, with a head no wider than 12 inches. Officials rarely measure a goalie pocket without cause, but a visibly bagged out pocket invites the check, and an illegal stick costs your team at the worst moment. String to the test, not to the edge of it.

Break In, Wet Weather, and Backup Heads

Goalie mesh stretches for weeks. Recheck depth after every practice for the first month, and expect to tighten the bottom string at least twice. Rain speeds the process dramatically: a pocket that was perfect on Saturday can be a laundry bag after one wet game, which is why serious goalies carry a second head strung to match. String the backup in the same session, with the same pattern and tensions, and rotate both heads in practice so they break in together. A backup that has never been thrown is not a backup. It is a science project waiting for your starter to break.

Worked Example: Tuning Out a Rebound Problem

A high school goalie gives up three rebound goals in two games. His pocket passes the outlet test beautifully, which is the clue: it was strung for clearing at the cost of control. His stringer loosens the top shooter slightly, deepens the bottom string by one hole, and pounds the mesh around a ball overnight. At the next practice the same firm shots die in the pocket eight times out of ten, and his outlets drop a little flatter, which he fixes with footwork rather than more string changes. The order matters: control first, trajectory second, because a rebound in the slot is a goal chance, while a slightly flat clear is just a pass.

Channel Shape: Narrow Top, Patient Middle

A goalie channel should be snug at the top so the ball exits on a predictable line, then open gradually into the pocket so a shot loses energy instead of hitting a wall. Stringers build that shape with sidewall tension: tighter and more vertical near the scoop, relaxing as the pattern moves down. If the channel pinches in the middle, outlet passes wobble and shots can stick and then drop unpredictably. If it never pinches at all, the ball swims in the pocket during a clear and the goalie loses the quick release that beats a ride.

Test the channel with a slow motion drill before any shooting: roll a ball down the pocket from the scoop twenty times and watch its path. A good channel rolls the ball straight out the center every time. A crooked roll at walking pace will be a crooked pass at game speed, and it is far easier to fix at the workbench than on the field.

Shooter Placement Patterns Worth Knowing

Most goalie pockets settle on one of three shooter families. Two straight shooters across the upper third give the simplest, most repeatable release and suit most developing goalies. Three shooters, with the top one slightly tighter, add hold for goalies whose clears keep sailing. A single nylon shooter near the scoop, used by some advanced stringers, sharpens the release point for long outlets but punishes a pocket that is even slightly asymmetric. Change shooter families one variable at a time and log the result, because a goalie who cannot describe her own pocket setup cannot ask a stringer to reproduce it.

Stringing for a Young Goalie Versus a Varsity Goalie

A youth goalie needs control above all: softer mesh, a slightly shallower bag than a varsity keeper would choose, and shooters set for a flat, forgiving release at short clearing distances. A varsity goalie facing harder shots can use the full depth the legality test allows and a channel tuned for thirty yard outlets. Stringing a ten year olds pocket to a college pattern is a common and expensive mistake, because the young keeper cannot yet throw out of a deep bag against a ride, and every failed clear costs her team a possession she just saved.

Breaking In a Fresh Goalie Pocket

A new goalie pocket lies about its depth for the first few sessions, because stiff mesh and fresh knots settle under real shot impact. Speed the process honestly: pound the pocket with a ball on a short rope or a pocket pounder for ten minutes, working the center channel first and then the corners where rebounds like to escape. Then take thirty practice shots at half speed and re-measure the depth with the ball-and-straightedge check before trusting it in a game. Expect the pocket to deepen noticeably during this first week, and plan one retensioning session where you snug the bottom string and the lower sidewall knots. Skip the shortcuts involving water soaking and weights overnight; they stretch mesh unevenly and can leave one quadrant baggier than the rest.

Frequently Asked Questions

What mesh is best for stringing a goalie head?

Most goalies use 12 diamond mesh because the large diamonds suit a head up to 12 inches wide, wrap the ball on saves, and soften rebounds. Soft mesh controls rebounds best, while semi hard mesh throws more consistently in wet weather.

How deep should a lacrosse goalie pocket be?

Deep enough to kill rebounds and hold the ball on a clear, but legal: the top of a ball placed in the pocket should not sit below the bottom edge of the sidewall under the standard test. Most goalies play best with the deepest point just below the center of the head.

Why do my outlet passes sail high from a new goalie pocket?

An open channel top and loose shooting strings let the ball leave late and high. Tighten or add a shooter in the upper third, confirm the top corners are locked down, and throw twenty test passes before changing the pocket depth.

How often does a goalie head need restringing?

When the mesh hardens, tears, or stretches past the point where bottom string adjustments restore legal depth and control. A starting goalie who plays year round often restrings once a season and keeps a matched backup ready.

Can a field player string a goalie head with field mesh?

It is a poor idea. Small diamond field mesh across a goalie head forms a hard, shallow surface that shots rebound off, and it rarely builds a channel wide enough for clean outlets. Use proper goalie mesh sized for the head.